"1 1.JPG 1.JPG (26.41 KiB) Viewed 1322 times
Refer to the exhibit. A pre-sales system engineer receives a diagram of the current network WAN connectivity from a customer. EIGRP is the routing protocol used on the WAN. Based on the default operation of EIGRP, which statement is true about the routing table on router R1? There is a single route to the 192.168.16.0/28 LAN via the use of the T1 connection. There is a single route to the 192.168.16.0/28 LAN via the use of the DSL connection. There is a single route to the 192.168.16.0/28 LAN via the use of the Metro Ethernet connection.***** EIGRP installs all three routes to the 192.168.16.0/28 LAN and load balances the traffic.
2 2.JPG 2.JPG (33.38 KiB) Viewed 1292 times
A new host needs to be connected to VLAN 1. Router RA is attached to the VTP trunk and configured as shown in the output contained in the graphic. Which of the following IP addresses should be assigned to this new host? 192.168.1.1 /26 192.168.1.11 /28 192.168.1.22 /28**** 192.168.1.33 /28 192.168.1.44 /28 192.168.1.55 /28
3 3.JPG 3.JPG (38.94 KiB) Viewed 1283 times
Refer to the exhibit. A NetworkingCompany designer is reviewing a diagram of a customer network. What two risks or issues can be identified in the topology that is shown? (Choose two.) The firewall router and ISP connection represent a single point of failure.**** A failure of the switch that connects the Cisco Call Manager to the network will cause the entire IP telephony system to fail.**** Using Layer 3 switches to interconnect the data center servers to the IP phones introduces too much delay. The IP phones need to be redundantly connected to the switches to prevent single points of failure at the access layer. If one of the Layer 3 switches fails, the Cisco Call Manager will be unreachable.
4 An engineer who is part of a sales team has been asked to select technologies and equipment capabilities to meet the network requirements of the prospective client. The engineer is also responsible for diagramming the placement and interconnection of various network devices and services. Which role is this engineer performing? post-sales field engineer account manager pre-sales engineer**** network designer
5 5.JPG 5.JPG (82.6 KiB) Viewed 1284 times
Refer to the exhibit. Two network engineers are setting up a prototype network to test a new Frame Relay network design. One of the engineers connects the cables and powers up all of the devices per the test plan. The second engineer uses a console cable to connect to the BR1 router, configures the Frame Relay connection and issues a show interfaces serial 2/0 command. What does the output of this command indicate to the engineers? A no shutdown command must be entered on the interface. The IP address has not yet been configured on the interface. The WAN encapsulation method is incorrect on the interface.
The cable that connects BR1 to FR2 may not be correct or is not connected properly.***
6 After an administrator installs a WIC into a two-slot router and issues the show version command, the newly installed interfaces in the WIC cannot be seen in the router output. What is a possible reason why the newly installed interfaces are not displayed in the router output? The interface is not configured properly. The WIC was put into slot 0 instead of slot 1. The WIC was not physically installed in the slot properly. The show version command cannot be used to validate the presence of installed interfaces.***
7 7.JPG 7.JPG (40.11 KiB) Viewed 1281 times
Refer to the exhibit. What can be concluded from the output that is shown? MDF_2811 has a MAC address of 2294:300F:0000. A Cisco 3750 switch is connected to the FastEthernet1/0/1 port on MDF_2811. MDF_2811 is installed in the main distribution facility on floor 28 of building 11. Device 3750-24_IDF2 is running Cisco IOS Software Release 12.2(25)SEE2.***
8 8.JPG 8.JPG (31.2 KiB) Viewed 1276 times
Refer to the exhibit. A network technician is performing an initial installation of a new switch in the east wing. The technician removes the switch from the box, connects the switch to a router that supports the 10.255.254.0/24 network, and adds the configuration that is shown. The technician notifies the network administrator that the switch has been installed. The network administrator then attempts to telnet to the switch from host 192.168.0.1 to complete the switch configuration. What are the results of this attempt to telnet?
The switch refuses the connection. The connection to the switch times out. The network administrator is prompted to login.**** The connection is established at the user EXEC prompt.
9 A NetworkingCompany customer is interested in creating an e-commerce business, which includes a network upgrade and the addition of a new server farm. By offering their products on the web, the company expects to increase revenue and reduce wait times to process orders. The network designer proposes to implement the server farm in a new data center and to add a new T1 circuit to handle the expected traffic. What are two business goals of the NetworkingCompany customer? (Choose two.) install a new T1 circuit increase revenue*** implement a new server farm reduce wait times to process orders*** install a new data center
10 10.JPG 10.JPG (19.7 KiB) Viewed 1274 times
Refer to the exhibit. To demonstrate the importance of using contiguous IP addressing in a hierarchical network design, a network designer configures a prototype network with the use of a network simulator. Which EIGRP configuration commands should the designer enter on router R1 to correctly advertise a single summary route to router BR1 for the campus LAN? 10a.JPG 10a.JPG (12.53 KiB) Viewed 1285 times
10b.JPG 10b.JPG (10.5 KiB) Viewed 1272 times
10c.JPG 10c.JPG (7.89 KiB) Viewed 1270 times
10d.JPG 10d.JPG (11.46 KiB) Viewed 1265 times
11 What makes the Cisco EasyVPN application a useful tool for VPN implementation? It provides encryption algorithms unavailable in other systems. It ensures that remote workers actually use the VPN for connectivity. It simplifies the configuration tasks for the device that is used as the VPN server.*** It allows a greater variety of network devices to be used for VPN connections.
12 A local car dealership recently purchased an automobile financing company. The owner of the dealership issues a contract to NetworkingCompany to integrate the finance company network into the car dealership network. A router in the existing finance company network requires a password for both Telnet and console access, but no one remembers the passwords. What can the NetworkingCompany network technician do to obtain or change the passwords and gain access to the router? Use a TFTP server to download a new configuration file to the router that contains the passwords used on the car dealership network and then reload the router. Connect a rollover cable to the serial0/0 port of the router in order to bypass the password security, and use the show running-config command to obtain the passwords. Connect a console cable to the router, power cycle the router, issue a Ctrl-Break to enter ROM monitor mode, and change the configuration register to bypass the startup configuration.*** Connect the router to another Cisco router at the car dealership, use the show cdp neighbors command to obtain an IP address of the router, and use SSH to gain secure access in order to view the passwords.
13 A network administrator is troubleshooting connectivity problems on a small IPv6 network that consists of two network segments that are connected by a single router. The administrator can ping the IP addresses of local hosts on each segment from the router. Hosts on one network segment cannot successfully ping the IP
addresses of hosts on the other network segment. What is the most likely cause of the connectivity problem between the segments? incorrect VLAN assignments on each segment broadcast storm that is caused by a malfunctioning NIC on a host incorrect DNS mappings of host names to IPv6 addresses IPv6 traffic forwarding not configured on the router***
14 At the distribution layer of a hierarchical network, what are two advantages of using Layer 3 devices instead of Layer 2 switches? (Choose two.) enables the creation of large multisite VLANs creates fewer IP subnets to configure and manage reduces the number of redundant links required reduces the complexity of STP configurations*** enables traffic filtering based on subnet addresses***
15 A NetworkingCompany engineer is on a support call resolving technical problems for a client network. After the issue is resolved, the engineer also provides a training session for the client's network support staff. Which position on the networking company team is this engineer performing? post-sales field engineer*** pre-sales engineer network designer account manager
16 What is the main purpose of the access layer in a hierarchically designed network? perform routing and packet manipulation supply redundancy and failover protection provide a high-speed, low-latency backbone serve as a network connection point for end-user devices***
17 A router has been removed from the network for maintenance. A new Cisco IOS software image has been successfully downloaded to a server and copied into the flash of the router. What should be done before placing the router back into service? Back up the new image. Copy the running configuration to NVRAM. Delete the previous version of the Cisco IOS software from flash. Restart the router and verify that the new image starts successfully.***
18 A NetworkingCompany customer requires VPN connectivity for workers who must travel frequently. To support the VPN server, the customer router must be upgraded to a new Cisco IOS software version with the Advanced IP Services feature set. What should the field engineer do before copying the new IOS to the router? Set the router to load the new IOS image file directly from the TFTP server on the next reboot. Delete the currently installed IOS by using the erase flash: command, and reload the router Issue the show running-configuration command to determine the features of the currently installed IOS image file. Issue the show version and the show flash commands to ensure that the router has enough memory and file space to support the new IOS image.***
19 The main office of a NetworkingCompany customer currently connects to three branch offices via three separate point-to-point T1 circuits. The customer network uses RIPv2 as the routing protocol within both the LAN and the WAN. The account manager proposes a change to a Frame Relay network because the costs are lower. A single local loop connection can be installed at the main office with three separate PVCs to connect the branch offices. How can the main office edge router be configured to enable the customer to continue to use RIP as the WAN routing protocol? Enable Inverse ARP on the serial interface in order to learn the routes to the IP addresses of the remote routers. To prevent the Frame Relay network from causing a routing loop, disable split horizon on the serial interface. Create three separate point-to-point subinterfaces on the serial interface and assign a different subnet IP address to each one.*** Configure the serial interface with a single interface DLCI number and create frame-relay map statements for each remote site address.
20 A high school uses a fractional T1 for Internet access. Wireless network access is provided in approximately 30 percent of the physical campus. Tests performed recently by the IT administrators indicate that the T1 circuit is operating at full capacity. The school district IT design team is asked to propose a network upgrade plan to address two business goals: 1. Provide wireless network connectivity for students in 90 percent of the physical campus. 2. Improve Internet access for all students and faculty. The design team proposes to upgrade the memory of the core router that is connected to the ISP and to purchase additional wireless access points. What can be concluded about the proposal that is presented by the design team? The proposal addresses only the goal to increase the wireless coverage.*** The proposal addresses only the goal to improve Internet access. The proposal addresses both business goals. The proposal addresses neither business goal.
21 21.JPG 21.JPG (24.54 KiB) Viewed 1262 times
Refer to the exhibit. The network administrator is configuring the port security feature on switch SWC. The administrator issued the command show port-security interface fa 0/2 to verify the configuration. What can be concluded from the output that is shown? (Choose three.) This port is currently up. The port is configured as a trunk link. There is no device currently connected to this port.*** Three security violations have been detected on this interface. Switchport mode for this interface is access-mode. Security violations will cause this port to shut down immediately.***
22 What are two advantages of using a simulation tool to test an IP addressing scheme? (Choose two.)
Address configuration errors can be addressed using out-of-band connections. Placement of subnets and route summarization can be verified. An engineer can test physical security without leaving the office or lab.*** The addressing scheme can be tested for scalability.*** The effects of combining new with existing infrastructure can be measured. It provides real-time monitoring of a production network.
23 23.JPG 23.JPG (30.64 KiB) Viewed 1257 times
Refer to the exhibit. A field engineer is called into a customer's office to determine a problem with connectivity in the network. Based on the customer's IP addressing scheme, what is causing the problem? The VLSM scheme is correct as shown. The WAN that connects R1 to R3 has an incorrect mask. The WAN that connects R1 to R2 overlaps with the R3 LAN.*** The R1 LAN is incorrect because subnet zero cannot be used with VLSM.
24 A new WIC is installed in an available router slot. At what point during the router startup process does the router test the card for hardware problems? after the configuration from NVRAM is loaded into RAM when the bootstrap program is loaded into RAM after the configuration from NVRAM is loaded into ROM during the power-on self-test (POST)***
25 25.JPG 25.JPG (75.24 KiB) Viewed 1257 times
Refer to the exhibit. A NetworkingCompany engineer is characterizing an existing network for a new customer. The engineer issues a show run command on the branch router to gather configuration information. What is the engineer able to determine as a result of viewing the output of this command? The branch office router has two routes to the main office LAN in the routing table.*** The default route for the branch office traffic is the router that is located at the main office. A connection through ISP-A will be used to reach the main office LAN if the Frame Relay network is unavailable. By using both the DSL and the Frame Relay connection, the branch office router will load balance traffic that is destined for the main office LAN.
26 A configuration file needs to be loaded into the RAM of a router from a TFTP server. What should an administrator know before accomplishing this task? the router IP address and the operating system that is used by the TFTP server the TFTP server IP address and the name of the configuration file on the server*** the router IP address and the name of the router configuration file in NVRAM the TFTP server IP address and the router interface through which the file will be loaded
27 A network designer must select a routing protocol for the network of a customer. The currently installed network contains both Cisco and non-Cisco routers, and there is no budget to replace them. The designer plans on implementing both VLSM and route summarization in the new network design. Which two protocols can provide the necessary functionality for this LAN? (Choose two.) RTP RSTP RIPv1 RIPv2*** EIGRP OSPF***
28 Which two weaknesses in a proposed network design can be identified by setting up a prototype network and performing tests on it? (Choose two.)
congestion and inadequate bandwidth in the provider Frame Relay network costs of the proposed equipment exceed the customer budget*** potential points of failure that are critical to the network*** limited scalability that can present problems if the network grows faster than anticipated poor documentation of existing network topology and design
29 A user in a large office calls tech support to complain that the PC no longer connects to the Internet or to any network resources, but seems otherwise normal. The help desk technician asks the caller to talk to nearby users to see if other machines are affected. After a few minutes, the caller reports that several immediate neighbors have the same problem, but those seated further away do not. Assuming that the description is accurate, what should be checked next? power outlet to the PC that is used by the caller workgroup switch in the telecommunications room**** cable between any network outlet and the telecommunications room cable between the PC that is used by the caller and the network outlet it connects to cable between the PC that is used by a neighbor and the network outlet the neighbor PC it connects to
30 Which of the following are characteristics of the core layer of the hierarchical network design model? (Choose three.) redundant paths*** high-level policy enforcement packet manipulation media transitions rapid forwarding of traffic no packet filtering 31 A network designer needs to perform prototype testing on a multisite network design to verify that failure domains are not larger than specified in the proposal. What would be the most efficient way to conduct this test?
Use simulation software to check the IP addressing scheme for errors. Power down lab equipment and ping from one host to all other hosts. Disconnect links between lab equipment and ping end-to-end across the network. Delete devices or links in simulation software and ping from each host to all other hosts.***
32 A customer has asked a network engineer to prototype the new IP addressing and summarization strategy for a large, multisite network implementation. Which tool is appropriate for testing the complete addressing scheme? Cisco SDM network simulation tool*** actual network equipment in a lab current network of the customer
33 During a review of the proposed bill of materials, the NetworkingCompany account manager realizes that the systems engineer included a lower cost, less capable switch model for the access layer connectivity than was specified by the network designer. When questioned, the systems engineer responds that the switches recommended by the designer cannot be purchased within the budget limitations of the customer. Which action should the account manager take? Inform the customer that the project cannot be completed given the unreasonable budget constraints. Communicate any risks associated with the equipment substitution and obtain customer approval to proceed.*** Because the customer is probably aware that the budget limitations will require lower cost, less capable equipment, the account manager should do nothing. Because the customer is probably aware that the budget limitations will require lower cost, less capable equipment, the account manager should do nothing.
34 34.JPG 34.JPG (22.28 KiB) Viewed 1256 times
Refer to the exhibit. What is the spanning-tree role of all the enabled interfaces of SW11?
alternate backup designated*** root
35 After performing a password recovery operation on a router, the network field engineer copies the running configuration to the startup configuration and then reloads the router. The router boots successfully but immediately enters the setup mode. The engineer manually loads the startup configuration using the copy s..."
|
You need to upgrade your Flash Player , or try to enable javascript in order see this document properly.
|
|
Comments
![Miley Cyrus on The Tyra Banks Show [Part 2/3] (flv video)](http://fliiby.com/images/_thumbs/tn_gdb8yaq86m1.jpg "Miley Cyrus on The Tyra Banks Show [Part 2/3] (flv video)")
